[How-To] Konfiguracja Neostrady - modem Sagem F@st 800

[POL_ED]

Przeglądnij jeszcze raz cały temat.
Może gdzieś popełniasz błąd. Innym działa.

Nie odpowiedziałeś czy jest wynik w dmesg co z eagle-usb ?

Podstawowe pliki konfiguracyjne
/etc/ppp/peers/neostrada

debug
kdebug 1
user rejestracja@neostrada.pl
asyncmap 0
lcp-echo-interval 2
lcp-echo-failure 7
plugin pppoatm.so
0.35
noauth
usepeerdns
noipdefault
defaultroute
holdoff 4
persist
maxfail 25

/etc/ppp/pap-secrets i /etc/ppp/chap-secrets

rejestracja@neostrada.pl    *   rejestracja    *

należy podać otrzymaną nazwę użytkownika w miejsce rejestraca@neostrada.pl

Przy tej zawartości plików powinien być wynik

ifconfig

ppp0      Link encap:Point-to-Point Protocol  
          inet addr:83.27.227.217  P-t-P:213.25.2.37  Mask:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:9178  Metric:1
          RX packets:175922 errors:0 dropped:0 overruns:0 frame:0
          TX packets:144799 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:3
          RX bytes:18388453 (17.5 MiB)  TX bytes:19310312 (18.4 MiB)

oczywiście IP będzie inne.

Którą wersję kernala masz ?

uname -r

Czy to nie jest najnowszy SEGEM FAST 800 E4 ?

========================
Z wyniku lsusb

Bus 001 Device 004: ID 1110:9021 Analog Devices Canada, Ltd (Allied Telesyn)

wskazuje na SEGEM F@st 800

Bus 001 Device 004: ID 1110:9031 Analog Devices Canada, Ltd (Allied Telesyn)

wskazuje na SEGEM F@st 800 E3T

Bus 001 Device 004: ID 1110:9041 Analog Devices Canada, Ltd (Allied Telesyn)

ten wynik wskazuje jednak na SEGEM FAST 800 E4

=============================================
Dla SEGEM FAST 800 E4

W systemie muszą być dostępne źródła kernela zgodne z używanym kernelem

rpm -qa|grep kernel

uname -r

Ze strony projektu należy pobrać firmware ueagle-atm4.tar.gz
Rozpakuj

 tar -xf ueagle-atm4.tar.gz

W konsoli przejdź do katalogu ueagle-atm4/driver i wykonaj:

make
make install

To skompiluje i zainstaluje moduł kernela ueagle4-atm. Polecenie "make install" musi być wykonane przez roota.
Następnie należy moduł przekopiować.

Następnie przejdź do ueagle-atm4/firmware i skopiuj firmware do /lib/firmware/ueagle-atm.

Wymagany eagle-usb-2.3.3

Sprawdź jako root w konsoli

modinfo ueagle-atm

jeżeli w wyniku znajdzie się

alias:          usb:v1110p9041d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p9042d*dc*dsc*dp*ic*isc*ip*

potwierdzi istnienie modułu do SEGEM FAST 800 E4

[popoo]

Czy to nie jest najnowszy SEGEM FAST 800 E4 ?

nie

uname -r

wywaliło:

2.6.17-5mdv

rpm -qa|grep kernel

wywaliło:

kernel-2.6.17.5mdv-1-1mdv2007.0
ati-kernel-2.6.17-5mdv-8.28.8-1mdk
kernel-source-stripped-2.6.17.5mdv-1-1mdv2007.0

spedziłem w sumie nad tym ok 10 godzin.... i chyba juz tarcę siły, instalowałem nawet te pod E4... wszystko jedno - modem widzi jako (null) ... a w konfiguracji dalej widnieje tylko sieciówka, macie jeszce jakiś pomysł? Bez netu mandriva ejst mi bezużyteczna wiec zapewne zniknie z mojego dysku.

[POL_ED]

Wynik lsusb jednoznacznie potwierdza, że to jest SEGEM FAST 800 E4

Dla kernel-2.6.17.5mdv-1-1mdv2007.0
ma być kernel-source-2.6.17.5mdv-1-1mdv2007.0

a nie kernel-source-stripped-2.6.17.5mdv-1-1mdv2007.0

Po make nie zgłasza żadnego błędu ?

[popoo]

Wynik lsusb jednoznacznie potwierdza, że to jest SEGEM FAST 800 E4

sprawdzałem to tak jak kazałeś:

Sprawdź jako root w konsoli

modinfo ueagle-atm

jeżeli w wyniku znajdzie się

alias:          usb:v1110p9041d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p9042d*dc*dsc*dp*ic*isc*ip*

potwierdiz istnienie modułu do SEGEM FAST 800 E4

nic takiego tam nei było, tutaj akurat ejstem pewien że nie mam E4

Dla kernel-2.6.17.5mdv-1-1mdv2007.0
ma być kernel-source-2.6.17.5mdv-1-1mdv2007.0

mozesz podać jakiegoś linka skad mozna to pobrać? Szukam na http://rpm.pbone.net ale na arzie bez efektów.

[POL_ED]

@ popoo,
Przeczytaj jeszcze raz to co napisałem.
O tym który model masz informuje wynik lsusb.

How-To
Czyli jak przygotować system do kopmilacji - w tym również drivera dla Twojego modemu.

Piszesz, że na pbone nie ma kernel-source dla Twojego kernela.
Po 1 minucie wynik http://rpm.pbone.net/index.php3?stat...007.0.i586.rpm

[wieczk]

Jestem ciekaw rozwiązania problemu.Ja również walczę od 2 dni wg podanych wskazówek i instrukcji z innych stron, aby zainstalować Sagem f@st 800 4E. Niestety na razie bez rezultatu.Modem nie jest widoczny, kiedy chcę go wybrać podczas konfiguracji łącza DSL,Linux wyświetla mi tylko interfejs ethernet.
Przeszukując liczne strony można napotkać informacje o poważnych problemach z instalacją tego modemu.No cóż, jak na razie informacje te zdają się potwierdzać.
A czy wogóle ktoś tutaj jest na forum, komu się udało już zanstalować ten modem pod Linuxem? Oczywiście chodzi o Sagem F@st 800 4E. Jutro dalszy ciąg zmagań.W końcu musi się dać rozwiązać ten problem.

[DRACO_WAHATEVER]

Ew. wymienić modem w tp na jakiś inny, lub kupić na alegro za kilka złotych .

Polecam speedtoucha 330 srebnego i czarnego .

[Shoto]

Jestem ciekaw rozwiązania problemu.Ja również walczę od 2 dni wg podanych wskazówek i instrukcji z innych stron, aby zainstalować Sagem f@st 800 4E. Niestety na razie bez rezultatu.Modem nie jest widoczny, kiedy chcę go wybrać podczas konfiguracji łącza DSL,Linux wyświetla mi tylko interfejs ethernet.
Przeszukując liczne strony można napotkać informacje o poważnych problemach z instalacją tego modemu.No cóż, jak na razie informacje te zdają się potwierdzać.
A czy wogóle ktoś tutaj jest na forum, komu się udało już zanstalować ten modem pod Linuxem? Oczywiście chodzi o Sagem F@st 800 4E. Jutro dalszy ciąg zmagań.W końcu musi się dać rozwiązać ten problem.

Mnie po wielu bojach udało się po 2 dniach zmusić go do pracy.

Tutaj dokładnie opisałam, jak to zrobiłam:
http://pclinuxos.vrs.pl/viewtopic.php?t=1461

[wieczk]

Wejdę w ten wątek, bo drążony problem wydaje się być identyczny z moim.
Niestety pomimo szczegółowych wskazówek przestawionych przez Pol_EDA i Shoto, Linux nie widzi modemu S@gem Fast 800 E4.
Może ktoś dopatrzy się błędu,który powoduje problem?
Źródła są dobre:

[root@localhost wieczk]# rpm -qa|grep kernel
kernel-source-2.6.17.13mdv-1-1mdv2007.1
kernel-2.6.17.13mdv-1-1mdv2007.1
kernel-latest-2.6.17-13mdv
[root@localhost wieczk]#

Co do kompilacji ueagle atm4 nie mam już pewności dlatego przedstawiam co wyrzucił Linux
(Poniżej błędy literowe już powstały w Windows)

[wieczk@localhost driver]$ su
[root@localhost driver]# make
make -C /lib/modules/2.6.17-13mdv/build M=/home/wieczk/ueagle-atm4/driver EXTRA_CFLAGS=-DDEBUG
make[1]: Wejście do katalogu `/usr/src/linux-2.6.17-13mdv'

  WARNING: Symbol version dump /usr/src/linux-2.6.17-13mdv/Module.symvers
           is missing; modules will have no dependencies and modversions.

  LD      /home/wieczk/ueagle-atm4/driver/built-in.o
  CC [M]  /home/wieczk/ueagle-atm4/driver/ueagle-atm.o
/home/wieczk/ueagle-atm4/driver/ueagle-atm.c: In function ‘uea_start_reset’:
/home/wieczk/ueagle-atm4/driver/ueagle-atm.c:1173: warning: unused variable ‘cmvs_fw’
/home/wieczk/ueagle-atm4/driver/ueagle-atm.c:1172: warning: unused variable ‘cmvs’
/home/wieczk/ueagle-atm4/driver/ueagle-atm.c:1171: warning: unused variable ‘len’
/home/wieczk/ueagle-atm4/driver/ueagle-atm.c:1171: warning: unused variable ‘i’
/home/wieczk/ueagle-atm4/driver/ueagle-atm.c:1170: warning: unused variable ‘zero’
/home/wieczk/ueagle-atm4/driver/ueagle-atm.c:1858:2: warning: #warning "iso need a patch : http://lists.infradead.org/pipermail/usbatm/2006-October/000883.html"
/home/wieczk/ueagle-atm4/driver/ueagle-atm.c: At top level:
/home/wieczk/ueagle-atm4/driver/ueagle-atm.c:563: warning: ‘check_dsp’ defined but not used
/home/wieczk/ueagle-atm4/driver/ueagle-atm.c:1124: warning: ‘request_cmvs’ defined but not used
  LD [M]  /home/wieczk/ueagle-atm4/driver/ueagle4-atm.o
  Building modules, stage 2.
  MODPOST
  CC      /home/wieczk/ueagle-atm4/driver/ueagle4-atm.mod.o
  LD [M]  /home/wieczk/ueagle-atm4/driver/ueagle4-atm.ko
make[1]: Opuszczenie katalogu `/usr/src/linux-2.6.17-13mdv'
[root@localhost driver]# make install
make -C /lib/modules/2.6.17-13mdv/build M=/home/wieczk/ueagle-atm4/driver modules_install
make[1]: Wejście do katalogu `/usr/src/linux-2.6.17-13mdv'
  INSTALL /home/wieczk/ueagle-atm4/driver/ueagle4-atm.ko
  DEPMOD  2.6.17-13mdvcustom
make[1]: Opuszczenie katalogu `/usr/src/linux-2.6.17-13mdv'
/sbin/depmod -ae
[root@localhost driver]#

Konfiguracja i kompilacja eagle-usb-2.3.3
Tutaj po konfiguracji, wyrzuca już w czasie kompilacji blędy.

[wieczk@localhost 2.3.3-E4-B2]$ su
[root@localhost 2.3.3-E4-B2]# ./configure
checking for gcc... gcc
checking for C compiler default output file name... a.out
checking whether the C compiler works... yes
checking whether we are cross compiling... no
checking for suffix of executables...
checking for suffix of object files... o
checking whether we are using the GNU C compiler... yes
checking whether gcc accepts -g... yes
checking for gcc option to accept ANSI C... none needed
checking for a BSD-compatible install... /usr/bin/install -c
checking whether ln -s works... yes
checking for dirent.h that defines DIR... yes
checking for library containing opendir... none required
checking how to run the C preprocessor... gcc -E
checking for egrep... grep -E
checking for ANSI C header files... yes
checking for sys/types.h... yes
checking for sys/stat.h... yes
checking for stdlib.h... yes
checking for string.h... yes
checking for memory.h... yes
checking for strings.h... yes
checking for inttypes.h... yes
checking for stdint.h... yes
checking for unistd.h... yes
checking fcntl.h usability... yes
checking fcntl.h presence... yes
checking for fcntl.h... yes
checking limits.h usability... yes
checking limits.h presence... yes
checking for limits.h... yes
checking netinet/in.h usability... yes
checking netinet/in.h presence... yes
checking for netinet/in.h... yes
checking for stdint.h... (cached) yes
checking for stdlib.h... (cached) yes
checking for string.h... (cached) yes
checking sys/ioctl.h usability... yes
checking sys/ioctl.h presence... yes
checking for sys/ioctl.h... yes
checking sys/socket.h usability... yes
checking sys/socket.h presence... yes
checking for sys/socket.h... yes
checking sys/time.h usability... yes
checking sys/time.h presence... yes
checking for sys/time.h... yes
checking syslog.h usability... yes
checking syslog.h presence... yes
checking for syslog.h... yes
checking for unistd.h... (cached) yes
checking for an ANSI C-conforming const... yes
checking for off_t... yes
checking for size_t... yes
checking whether time.h and sys/time.h may both be included... yes
checking whether struct tm is in sys/time.h or time.h... time.h
checking for working volatile... yes
checking whether closedir returns void... no
checking whether gcc needs -traditional... no
checking for stdlib.h... (cached) yes
checking for GNU libc compatible malloc... yes
checking for working memcmp... yes
checking for stdlib.h... (cached) yes
checking for GNU libc compatible realloc... yes
checking sys/select.h usability... yes
checking sys/select.h presence... yes
checking for sys/select.h... yes
checking for sys/socket.h... (cached) yes
checking types of arguments for select... int,fd_set *,struct timeval *
checking return type of signal handlers... void
checking whether lstat dereferences a symlink specified with a trailing slash... yes
checking whether stat accepts an empty string... no
checking for strftime... yes
checking for alarm... yes
checking for gettimeofday... yes
checking for memset... yes
checking for select... yes
checking for socket... yes
checking for strcspn... yes
checking for strdup... yes
checking for strerror... yes
checking for strncasecmp... yes
checking for strspn... yes
checking for strtol... yes
checking for ifconfig... yes
checking for route... yes
checking for pidof... yes
checking for dhclient... dhclient
checking for pppd... yes
checking for pppoe... no
checking for tclsh... no
checking for wish... no
checking for xsltproc... yes
   *** libxslt-proc package is missing, keeping prebuild version ***
checking for kernel version... 2.6.17-13mdv
checking for ifup... 1
checking for adictrl... no
checking for eaglectrl... no
checking for showstat... no
checking for eaglestat... no
checking for startadsl... no
checking for stopadsl... no
configure: creating ./config.status
config.status: creating Makefile.common
config.status: executing default commands

========================================================================
distribution detected                           Mandrake

dhcp support                                    dhclient

pppd support                                    yes
  pppoa support                                 yes
  pppoe support                                 no  (runtime detection)

install eagleconnect (tcl/tk frontend)          no

generate documentation                          no
========================================================================

[root@localhost 2.3.3-E4-B2]# make
make -C driver
make[1]: Wejście do katalogu `/home/wieczk/2.3.3-E4-B2/driver'
USE_CMVS=1 make  -C /lib/modules/2.6.17-13mdv/build SUBDIRS=/home/wieczk/2.3.3-E4-B2/driver modules
make[2]: Wejście do katalogu `/usr/src/linux-2.6.17-13mdv'

  WARNING: Symbol version dump /usr/src/linux-2.6.17-13mdv/Module.symvers
           is missing; modules will have no dependencies and modversions.

  CC [M]  /home/wieczk/2.3.3-E4-B2/driver/eu_main.o
/home/wieczk/2.3.3-E4-B2/driver/eu_main.c:277: error: expected ‘)’ before string constant
/home/wieczk/2.3.3-E4-B2/driver/eu_main.c: In function ‘eu_user’:
/home/wieczk/2.3.3-E4-B2/driver/eu_main.c:1666: warning: ISO C90 forbids mixed declarations and code
make[3]: *** [/home/wieczk/2.3.3-E4-B2/driver/eu_main.o] BĹ‚Ä…d 1
make[2]: *** [_module_/home/wieczk/2.3.3-E4-B2/driver] BĹ‚Ä…d 2
make[2]: Opuszczenie katalogu `/usr/src/linux-2.6.17-13mdv'
make[1]: *** [eagle-usb.ko] BĹ‚Ä…d 2
make[1]: Opuszczenie katalogu `/home/wieczk/2.3.3-E4-B2/driver'
make: *** [build] BĹ‚Ä…d 2
[root@localhost 2.3.3-E4-B2]#

lsusb

[root@localhost wieczk]# lsusb
Bus 005 Device 006: ID 0930:651c Toshiba Corp.
Bus 005 Device 001: ID 0000:0000
Bus 004 Device 002: ID 043d:005c Lexmark International, Inc.
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 004: ID 1110:9042 Analog Devices Canada, Ltd (Allied Telesyn)
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
[root@localhost wieczk]#

Modinfo ueagle-atm

[wieczk@localhost ~]$ su
[root@localhost wieczk]# modinfo ueagle-atm
filename:       /lib/modules/2.6.17-13mdv/kernel/drivers/usb/atm/ueagle-atm.ko.gz
license:        Dual BSD/GPL
description:    ADI 930/Eagle USB ADSL Modem driver
author:         Damien Bergamini/Matthieu Castet/Stanislaw W. Gruszka
alias:          usb:v0BAFp00F7d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v0BAFp00F8d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v0BAFp00F5d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v0BAFp00F6d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v0BAFp00F9d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v0BAFp00FAd*dc*dsc*dp*ic*isc*ip*
alias:          usb:v0BAFp00F1d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v0BAFp00F2d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p9031d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p9032d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p9023d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p9024d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p9021d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p9022d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p900Fd*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p9010d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v05CCp3350d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v05CCp3351d*dc*dsc*dp*ic*isc*ip*
depends:        usbcore,usbatm
vermagic:       2.6.17-13mdv SMP mod_unload 686 gcc-4.1
parm:           debug:module debug level (0=off,1=on,2=verbose) (uint)
parm:           use_iso:use isochronous usb pipe for incoming traffic (array of bool)
parm:           sync_wait:wait the synchronisation before starting ATM (array of bool)
parm:           cmv_file:file name with configuration and management variables (array of charp)
[root@localhost wieczk]#

Dmesg

[wieczk@localhost ~]$ su
[root@localhost wieczk]# dmesg
Linux version 2.6.17-13mdv (rtp@octopus.mandriva.com) (gcc version 4.1.2 20070302 (prerelease) (4.1.2-1mdv2007.1)) #1 SMP Fri Mar 23 19:03:31 UTC 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007f7f0000 (usable)
 BIOS-e820: 000000007f7f0000 - 000000007f7f3000 (ACPI NVS)
 BIOS-e820: 000000007f7f3000 - 000000007f800000 (ACPI data)
 BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
1143MB HIGHMEM available.
895MB LOWMEM available.
found SMP MP-table at 000f4cd0
On node 0 totalpages: 522224
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 225279 pages, LIFO batch:31
  HighMem zone: 292849 pages, LIFO batch:31
DMI 2.4 present.
ACPI: RSDP (v000 GBT                                   ) @ 0x000f6650
ACPI: RSDT (v001 GBT    GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x7f7f3040
ACPI: FADT (v001 GBT    GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x7f7f30c0
ACPI: HPET (v001 GBT    GBTUACPI 0x42302e31 GBTU 0x00000098) @ 0x7f7f6d40
ACPI: MCFG (v001 GBT    GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x7f7f6dc0
ACPI: MADT (v001 GBT    GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x7f7f6c80
ACPI: SSDT (v001  PmRef  Cpu0Ist 0x00003000 INTL 0x20040311) @ 0x7f7f6e40
ACPI: SSDT (v001  PmRef    CpuPm 0x00003000 INTL 0x20040311) @ 0x7f7f72d0
ACPI: DSDT (v001 GBT    GBTUACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7f800000:70800000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=linux root=/dev/sda8  resume=/dev/sda9 splash=silent vga=normal
bootsplash: silent mode.
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2065176k/2088896k available (2430k kernel code, 21952k reserved, 760k data, 244k init, 1171396k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Using HPET for base-timer
Using HPET for gettimeofday
Detected 2152.068 MHz processor.
Using hpet for high-res timesource
Calibrating delay using timer specific routine.. 4307.32 BogoMIPS (lpj=8614649)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e39d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000e39d 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e39d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
checking if image is initramfs... it is
Freeing initrd memory: 843k freed
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
CPU0: Intel Genuine Intel(R) CPU            2160  @ 1.80GHz stepping 02
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4304.16 BogoMIPS (lpj=8608334)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e39d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000e39d 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e39d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU            2160  @ 1.80GHz stepping 02
Total of 2 processors activated (8611.49 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=4000
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 16 devices
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:0c: ioport range 0x400-0x4bf could not be reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1e.0
  IO window: a000-afff
  MEM window: e0000000-e1ffffff
  PREFETCH window: 80000000-800fffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1187797022.892:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
NET: Registered protocol family 1
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI wakeup devices:
PCI0 PEX0 PEX1 PEX2 PEX3 PEX4 PEX5 HUB0 UAR1 UAR2 USB0 USB1 USB2 USB3 USBE AZAL
ACPI: (supports S0 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Freeing unused kernel memory: 244k freed
SCSI subsystem initialized
libata version 1.20 loaded.
ata_piix 0000:00:1f.2: version 1.05
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
input: AT Translated Set 2 keyboard as /class/input/input0
ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:bc01 87:4023 88:20ff
ata1: dev 0 ATA-7, max UDMA7, 488395055 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
  Vendor: ATA       Model: SAMSUNG SP2504C   Rev: VT10
  Type:   Direct-Access                      ANSI SCSI revision: 05
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15
ata2: dev 0 cfg 49:0b00 82:0210 83:1000 84:0000 85:0000 86:0000 87:0000 88:101f
ata2: dev 0 ATAPI, max UDMA/66
input: ImExPS/2 Generic Explorer Mouse as /class/input/input1
ata2: dev 0 configured for UDMA/66
scsi1 : ata_piix
  Vendor: LITE-ON   Model: DVDRW SOHW-1693S  Rev: KS02
  Type:   CD-ROM                             ANSI SCSI revision: 05
SCSI device sda: 488395055 512-byte hdwr sectors (250058 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 488395055 512-byte hdwr sectors (250058 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 >
sd 0:0:0:0: Attached scsi disk sda
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ts: Compaq touchscreen protocol output
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000b000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 16, io base 0x0000b400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000bc00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 17, io mem 0xe20c0000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 3-1: USB disconnect, address 2
usb 5-6: new high speed USB device using ehci_hcd and address 3
usb 5-6: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb 3-1: new full speed USB device using uhci_hcd and address 3
usb 3-1: configuration #1 chosen from 1 choice
usb 4-2: new full speed USB device using uhci_hcd and address 2
usb 4-2: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x043D pid 0x005C
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
  Vendor: Kingston  Model: DataTraveler 2.0  Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sdb: 246272 512-byte hdwr sectors (126 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 246272 512-byte hdwr sectors (126 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
 sdb: sdb1
sd 2:0:0:0: Attached scsi removable disk sdb
usb-storage: device scan complete
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
sd 2:0:0:0: Attached scsi generic sg2 type 0
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945G Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
hw_random hardware driver 1.0.0 loaded
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
EXT3 FS on sda8, internal journal
Adding 4128664k swap on /dev/sda9.  Priority:-1 extents:1 across:4128664k
Supermount version 2.0.4 for kernel 2.6
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
loop: loaded (max 8 devices, max 1 partitions per device)
Netfilter messages via NETLINK v0.30.
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 224 bytes per conntrack
Using specific hotkey driver
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Processor [CPU1] (supports 2 throttling states)
Removing netfilter NETLINK layer.
ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 19 (level, low) -> IRQ 16
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 224 bytes per conntrack
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
[drm] Initialized i915 1.4.0 20060119 on minor 0
ClusterIP Version 0.8 loaded successfully
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 21 (level, low) -> IRQ 20
eth0: RTL8169sc/8110sc at 0xf8ea0000, 00:1a:4d:6b:14:ed, IRQ 20
Linux video capture interface: v1.00
usbcore: registered new driver ov51x
/home/wieczk/ov51x-jpeg-0.5.4/ov51x.c: v1.65-1.11-mark : ov51x USB Camera Driver
/home/wieczk/ov51x-jpeg-0.5.4/ov519_decomp.c: v1.4 : OV519 JPEG Decompression Module
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
NET: Registered protocol family 8
NET: Registered protocol family 20
[ueagle-atm] driver ueagle 1.3 loaded
usbcore: registered new driver ueagle-atm
usb 3-1: USB disconnect, address 3
usb 3-1: new full speed USB device using uhci_hcd and address 4
usb 3-1: configuration #1 chosen from 1 choice
usb 5-6: USB disconnect, address 3
usb 5-6: new high speed USB device using ehci_hcd and address 6
usb 5-6: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
  Vendor: Kingston  Model: DataTraveler 2.0  Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sdb: 246272 512-byte hdwr sectors (126 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 246272 512-byte hdwr sectors (126 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
 sdb: sdb1
sd 3:0:0:0: Attached scsi removable disk sdb
sd 3:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
[root@localhost wieczk]#

[POL_ED]

Polecenie make jako user a nie jako root
Następnie jako root

make install

To skompiluje i zainstaluje moduł kernela ueagle4-atm.
Przekopiowac i załadowac moduł.

Przejdź do ueagle-atm4/firmware i skopiuj firmware do /lib/firmware/ueagle-atm.

Sprawdź jako root w konsoli

modinfo ueagle-atm

jeżeli w wyniku wśród ninnych znajdzie się

alias:          usb:v1110p9041d*dc*dsc*dp*ic*isc*ip*
alias:          usb:v1110p9042d*dc*dsc*dp*ic*isc*ip*

oznaczać to będzie poprawne skompilowanie modułu.

Wynik

Bus 003 Device 004: ID 1110:9042 Analog Devices Canada, Ltd (Allied Telesyn)

wskazuje na brak załadowania firmware.


Dla E4 są paczki rpm w FARMIE