Witaj Gościu, jeżeli to czytasz to znaczy że nie jesteś zarejestrowany/zalogowany. Kliknij by się zarejestrować. Rejestracja zajmie mniej niż 30 sekund , a dzięki temu zniknie Ci ten dymek oraz będziesz miał pełne możliwośći personalizacji forum do własnych potrzeb.
problem z kamerą LUMENERA IP
Pokaż wyniki od 1 do 2 z 2

Temat: problem z kamerą LUMENERA IP

  1. #1
    Dołączył
    Oct 2007
    Postów
    6
    Wątków
    4
    Downloads
    0
    Uploads
    0
    Siła Reputacji
    0
    Reputacja
    1

    problem z kamerą LUMENERA IP

    Witam wszystkich.
    Mam trochę nieżywą kamerę IP LUMENERA. Nie podnosi się jej obsługa sieci.
    Udało mi się z nią porozumieć przez port RS ale niestety nie mam umiejętności, żeby ją "podnieść" na IP, co umożliwi mi wgranie nowego firmwaru.
    Jak kamera startuje to ma coś takiego:

    U-Boot 1.1.3 (May 22 2007 - 15:02:58) explorer2 build 4846
    U-Boot code: 50F80000 -> 50F9EA54 BSS: -> 50FA3160
    RAM Configuration:
    Bank #0: 50000000 64 MB
    Flash: 16 MB
    In: serial
    Out: serial
    Err: serial
    Net: identify the ethernet chip on board... Initialize: LAN91111 (0x3392) detected.

    SMC91111: PHY auto-negotiate timed out
    Using MAC Address 00:0B:E2:0D:0C:03
    Enter password in 3 seconds to enter bootloader:
    ## Booting image at 3c030000 ...
    Image Name:
    Image Type: ARM Linux Kernel Image (gzip compressed)
    Data Size: 606284 Bytes = 592.1 kB
    Load Address: 50008000
    Entry Point: 50008000
    Verifying Checksum ... Bad Data CRC
    ## Booting image at 20030000 ...
    Image Name:
    Image Type: ARM Linux Kernel Image (gzip compressed)
    Data Size: 606284 Bytes = 592.1 kB
    Load Address: 50008000
    Entry Point: 50008000
    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK

    Starting kernel ...
    cramfs: wrong magic
    umKernel panic: No init found. Try passing init= option to ke
    rnel.


    Kamera ma dwa zestawy bootujące:

    bootcmd2=setenv bootargs mem=$(kernel_mem)M $(console) smc91x=$(ethaddr) ip=off
    root=/dev/mtdblock8; bootm 20030000; run bootcmd3

    bootcmd=setenv bootargs $(console) mem=$(kernel_mem)M smc91x=$(ethaddr) ip=off r
    oot=/dev/mtdblock3; bootm 3c030000; run bootcmd2


    Uzyskałem jeszcze coś takiego po małej modyfikacji boota:

    explorer2> setenv kernel_mem 12
    explorer2> setenv ram_size 64
    explorer2> setenv max_jpeg_size=20000
    explorer2> saveenv
    Saving Environment (<NULL>)...
    Un-Protected 1 sectors
    Erasing Flash...
    done
    Erased 1 sectors
    Writing to Flash... Protected 1 sectors
    Protected 1 sectors
    explorer2> setenv bootfix setenv bootargs mem=$(kernel_mem)M ip=off root=/dev/mt
    dblock8\;bootm 20030000;

    explorer2> run bootfix

    ## Booting image at 20030000 ...
    Image Name:
    Image Type: ARM Linux Kernel Image (gzip compressed)
    Data Size: 606284 Bytes = 592.1 kB
    Load Address: 50008000
    Entry Point: 50008000
    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK

    Starting kernel ...

    Linux version 2.4.24-uc0 (rgb@sunny) (gcc version 3.3.4) #1 Tue May 22 15:03:32
    EDT 2007
    CPU: Arm922Tid(wb) revision 0
    Machine: Explorer2
    alloc_bootmem_low
    memtable_init
    Security risk: creating user accessible mapping for 0xc0000000 at 0xe0000000
    On node 0 totalpages: 3072
    zone(0): 3072 pages.
    zone(1): 0 pages.
    zone(2): 0 pages.
    Kernel command line: mem=12M ip=off root=/dev/mtdblock8
    explorer2_init_irq
    Calibrating delay loop... 99.73 BogoMIPS
    Memory: 12MB = 12MB total
    Memory: 10668KB available (1127K code, 255K data, 52K init)
    Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
    Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
    Mount cache hash table entries: 512 (order: 0, 4096 bytes)
    Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
    Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
    POSIX conformance testing by UNIFIX
    calling rest_init()
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Initializing RT netlink socket
    Starting kswapd
    JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
    i2c-core.o: i2c core module
    i2c-dev.o: i2c /dev entries driver module
    i2c-core.o: driver i2c-dev dummy driver registered.
    i2c-algo-bit.o: i2c bit algorithm module
    ttyS0 at MMIO 0xcb000000 (irq = 12) is a AMBA PrimeCell PL011
    ttyS1 at MMIO 0xcc000000 (irq = 18) is a AMBA PrimeCell PL011
    RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
    eth0: SMC91C11xFD(rev:2) 32-bit at 0xf7000300 IRQ:84 ADDR: 00:0b:e2:00:00:00
    SMC91x driver for Linux $Revision: 1.8 $
    Explorer2 mapping:size 400000 at 3c000000
    Explorer2 mapping:size 400000 at 20000000
    ZEUS:explorer2_map.map_priv_1=c107e000
    ZEUS:explorer2_map.map_priv_2=c147f000
    Amd/Fujitsu Extended Query Table v1.3 at 0x0040
    number of CFI chips: 1
    cfi_cmdset_0002: Disabling fast programming due to code brokenness.
    Creating 9 MTD partitions on "Explorer2 Flash map 1":
    0x00000000-0x00020000 : "U-Boot 1"
    0x00020000-0x00030000 : "Params 1"
    0x00030000-0x00100000 : "Kernel 1"
    0x00100000-0x00400000 : "RomFS 1"
    0x00400000-0x00430000 : "placeholder"
    0x00400000-0x00420000 : "U-Boot 2"
    0x00420000-0x00430000 : "Params 2"
    0x00430000-0x00500000 : "Kernel 2"
    0x00500000-0x00800000 : "RomFS 2"
    ZEUS:right end of init_explorer2(I mean flash)
    Lumenera RTC I2C initialized
    i2c-dev.o: Registered 'Lumenera Explorer2 RTC' as minor 0
    i2c-core.o: adapter Lumenera Explorer2 RTC registered as adapter 0.
    Lumenera I2C initialized
    i2c-dev.o: Registered 'Lumenera Explorer2 Imager' as minor 1
    i2c-core.o: adapter Lumenera Explorer2 Imager registered as adapter 1.
    NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP, IGMP
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 512 bind 1024)
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
    cramfs: wrong magic
    jffs2_scan_inode_node(): Data CRC failed on node at 0x00200000: Read 0xce9c7766,
    calculated 0x309c7e4e

    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200590: 0x2738 in
    stead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200594: 0xa629 in
    stead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200598: 0x565e in
    stead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0020059c: 0x4d41 in
    stead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x002005a0: 0xf750 in
    stead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x002005a4: 0x28dd in
    stead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x002005a8: 0x5785 in
    stead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x002005ac: 0x4e7e in
    stead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x002005b0: 0xd3ca in
    stead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x002005b4: 0xeee5 in
    stead
    Further such events for this erase block will not be printed
    VFS: Mounted root (jffs2 filesystem).
    Freeing init memory: 52K
    Unknown INCOMPAT nodetype FFFF at 001CA9B8
    Unknown INCOMPAT nodetype FFFF at 00000604
    jffs2_read_inode(): No data nodes found for ino #15
    jffs2_read_inode(): But it has children so we fake some modes for it
    Unknown INCOMPAT nodetype FFFF at 001C8A90
    jffs2_read_inode(): No data nodes found for ino #172
    Warning -5: unable to open an initial console.
    Unknown RWCOMPAT_COPY nodetype 5303 at 00261BD4
    Unknown INCOMPAT nodetype FFFF at 001ADCE8
    Unknown INCOMPAT nodetype FFFF at 000FB484
    Unknown INCOMPAT nodetype FFFF at 001C8848
    jffs2_read_inode(): No data nodes found for ino #167
    Node CRC f80d9ad5 != calculated CRC a204c0f7 for node at 0006b5c0
    Unknown INCOMPAT nodetype FFFF at 001C7AE4
    jffs2_read_inode(): No data nodes found for ino #138
    Node CRC 46d5868b != calculated CRC 1a81347f for node at 00082de4
    Unknown RWCOMPAT_DELETE nodetype 0000 at 001D0174
    Unknown INCOMPAT nodetype FFFF at 00000814
    Unknown INCOMPAT nodetype FFFF at 001CD9E0
    jffs2_read_inode(): No data nodes found for ino #261
    Node CRC 46d5868b != calculated CRC 1a81347f for node at 00082de4


    Czy ktoś może mi wytłumaczyć co jest z tym nie tak?
    Pozdrawiam.

  2. #2
    Dołączył
    Oct 2007
    Postów
    6
    Wątków
    4
    Downloads
    0
    Uploads
    0
    Siła Reputacji
    0
    Reputacja
    1

    Odp: problem z kamerą LUMENERA IP

    I nic.
    Chyba nikt nie miał do czynienia z taką kamerą.
    Albo nawet z takim linux-em.
    Szkoda, bo do końca tygodnia muszę podjąć decyzję o przekazaniu jej do serwisu lub na złom.

Informacje o wątku

Users Browsing this Thread

Aktualnie 1 użytkownik(ów) przegląda ten wątek. (0 zarejestrowany(ch) oraz 1 gości)

Uprawnienia

  • Nie możesz zakładać nowych wątków
  • Nie możesz pisać wiadomości
  • Nie możesz dodawać załączników
  • Nie możesz edytować swoich postów
  •